9/01/18

VMAC G30 SOLVES COMMON AIR COMPRESSOR CHALLENGES

Common Air Compressor Challenges


To celebrate the recent launch of the VMAC G30 Gas Engine Driven Air Compressor, now powered by Honda, VMAC ran a G30 Giveaway Contest. (Watch the video on our Facebook page!) In this contest we asked entrants to answer three simple questions. One of these questions asked fleet managers and operators what their top challenges with their current truck-mounted air compressors are. Here are the results:

Common Air Compressor Challenges

With seven options to choose from, the top three results were size, air output and weight, accounting for almost 60% of the responses. The VMAC G30 was designed and engineered to address the concerns fleet managers and operators have with their current equipment.

SIZE

VMAC G30 Gas Drive Air CompressorAir compressor size was the number one challenge our survey identified. The VMAC G30 is 50% smaller* than other competitive air compressors, measuring just 34” (l) x 21.5” (w) x 24” (h), making it small enough to fit on the side pack of a single rear wheel service body. The compact size frees up to 15 cubic feet on the truck body, and leaves more room in the back of the truck for supplies, tools, and equipment. Another bonus is that visibility is improved, as the short height of the G30 means it won’t obstruct the view in the rear window.

VMAC G30 Gas Drive Air Compressor

AIR OUTPUT

Not only is the G30 compact, it is also powerful—50% more powerful* than other competitive air compressors. Producing 30 CFM 100% of the time, the G30 can operate at 100% duty cycle, which means you won’t have to wait for air to build, and you can work without interruption, thanks to continuous air supply. The G30 doesn’t need a large air receiver tank either, which aids in the size challenge.

WEIGHT

Weight challenges are minimized with the VMAC G30, which weighs 50% less* than other competitive air compressors. Weighing just 205 lbs (93 kg), the G30 is over 200 lbs lighter. Not only does every pound of GVW count when building a truck service body, especially because vehicle weight restrictions vary by state, but the Environmental Protection Agency reports that for every 100 lbs of weight reduction, a vehicle’s fuel economy can increase by up to 2%. This means that with 200lbs less weight, the VMAC G30 can save you up to 4% in truck fuel costs.

*Compared to competing 22 to 30 CFM reciprocating gas engine driven air compressors, with 30-gallon air receiver tank.

OPERATING IN COLD TEMPERATURES

Respondents in Canada and the Northeast and Midwestern states noted operating air compressors in cold temperatures to be particularly challenging. To ensure the air compressor can operate in extreme cold, a cold climate kit can be installed on the G30. The G30 with cold climate kit is proven to start-up at temperatures of -30°C (-22°F).**

**Due diligence and additional care may be required for prolonged operation in temperatures reaching below -15°C (5°F).

TRANSFERABILITY

The VMAC G30’s lightweight and compact design makes it easier to transfer than heavier air compressors weighing over 400 lbs. The lifting hook makes for easy installation on the service truck as well.

MAINTENANCE

The VMAC G30 is easy to maintain, with servicing recommended every 200 hours or every 6 months. The compressor is oil injected; oil forms a seal between the rotors so they don’t wear against each other. The G30 compressor doesn’t contain any gears, reed-valves, piston rings, or components that will fatigue or become fouled, which means with proper servicing and operation, the compressor should never require rebuilding. The G30 comes with a VMAC Lifetime Limited Warranty, and the reliable Honda GX390 engine comes with a 3-year warranty (limited).

OPERATING IN HOT TEMPERATURES

Operating air compressors in hot temperatures was a concern for some operators and fleet managers, predominately those located in areas like Texas, Virginia, Arizona, and California. The G30 is proven to operate at temperatures up to 40°C (104°F) and is protected by a compressor oil temperature switch that opens at 140°C (284°F) and shuts down and disables the engine until the oil temperature drops below 139°C (282°F).

MINIMIZE CHALLENGES WITH THE VMAC G30

Each of these seven challenges can be addressed with upgrading your air compressor to the VMAC G30 Gas Engine Driven Air Compressor. Not only is it 50% smaller, 50% lighter, and 50% more powerful, but it is also proven to operate in the most extreme climates. It’s also easy to transfer and maintain, allowing you to spend your time on the job, not struggling with your equipment.

Learn more about the VMAC G30, or find a dealer. You can also find a VMAC Sales Rep—they’ll be happy to answer your questions, and provide you with a demo of the air compressor, so you can see the G30 in action for yourself.

No comments:

Post a Comment